Anycubic Photon P1 vs Photon Mono M7 Pro: Which Resin Workflow Fits You?
Choose the Anycubic Photon P1 if an optional two-material setup and its Wave Release film system suit your projects. Choose the Photon Mono M7 Pro if automatic resin refill and withdrawal are more useful to your routine. Both have heated vats. Their manufacturer-listed nominal build dimensions are similar, but an M7 Pro sample slicer profile differs in its Y extent, so check the usable space in the exact current profile. Neither feature list establishes a speed or print-quality winner. GoodPrints3D has not tested either printer for this comparison.
Compare the exact Photon P1 and Photon Mono M7 Pro configurations at Anycubic. Check the plug and bundle contents. The P1 Max and the non-Pro M7 are different models.
The practical differences
| Question | Photon P1 | Photon Mono M7 Pro |
|---|---|---|
| Manufacturer-listed nominal build volume | 223 × 126 × 230 mm | 223 × 126 × 230 mm, per Anycubic; the official sample profile uses a different Y extent. Check the current exact-model profile before planning a job. |
| Resin workflow | Optional dual-color and dual-material platform; base vat is manually filled | Auto-fill unit supports refill and withdrawal; check bundle |
| Temperature | Temperature-controlled standard vat, adjustable 20 to 40 °C | Dynamic temperature-controlled vat |
| Release film | Wave Release system with NFEP film | Improved ACF film listed by Anycubic |
Anycubic lists the M7 Pro nominal volume as 223 × 126 × 230 mm; its manual gives 223.64 × 126.48 × 230 mm, while an official exact-model sample slicer profile uses a different Y extent. These are planning figures, not proof that the two usable envelopes are identical. Check the complete supported job in the current exact-model profile and allow room for rafts, supports and orientation. Exposure, resin, supports, layer height and finishing all matter.
Two materials or less manual filling?
The P1's dual-color and dual-material platform is an optional separate setup, not a built-in capability of every base package. It can let you run separate small parts in different resins in the same session, but it adds setup and cleaning. Check the current kit instructions, usable space and supported software before planning a job. In its April 2026 P1 review, Tom's Hardware reported glitches in dual-plate slicing. That is a time-specific observation, so check the current software version.
On the M7 Pro, Anycubic describes a unit that feeds resin to the vat and withdraws it. This addresses replenishment and recovery, not two-material printing. Confirm the unit is included in the selected package, check bottle and resin compatibility, and follow the current instructions. Automation still requires inspection and cleaning. In its M7 Pro review, Tom's Hardware reported that its test unit's refill pump did not work. That is one test unit, not a failure-rate estimate.
Heat, film and maintenance
Anycubic lists temperature-controlled vats for both models. Heat can help maintain a working temperature, but resin formulation, ambient conditions and exposure settings still matter. Confirm the temperature requirements of the resin and the configuration you intend to use. Do not assume the P1's optional dual-material setup has the same heating arrangement as its standard vat.
Anycubic describes the P1's Wave Release system as reducing peel forces as each layer separates from the film. The M7 Pro listing specifies ACF film. Both films wear and need inspection and eventual replacement; their names alone do not tell you which will last longer or produce better parts. Follow the correct model-specific replacement procedure. Owen Marsh's P1 assessment at 3D Printer World cautions against assuming the manufacturer's claimed peel-force improvement applies to every job.
The M7 Pro adds a fluid path to maintain. Tom's Hardware also describes cleaning the heated vat's circulation path when changing resin. Follow the current manufacturer instructions for each component rather than soaking electrical parts.
Materials, setup and running costs
Both are LCD resin printers, so plan for liquid resin handling, washing and post-curing. Anycubic lists standard, water-washable, ABS-like, plant-based and high-speed resins for the M7 Pro and says the P1 supports its resins. These are compatibility descriptions, not tests of every formulation. Check each resin's instructions, calibrate exposure and verify that its viscosity and temperature are suitable for any automatic feed system. Water-washable resin still requires safe handling and disposal.
Photon Workshop is listed for both; Anycubic also lists other slicers, with version and workflow limitations. Verify the exact machine profile and dual-platform support before choosing software. For either printer, budget for resin, film, cleaning supplies, protective equipment, wash and cure equipment, electricity and failed or calibration prints. The P1 kit and the M7 Pro's feed components add their own maintenance considerations. Use appropriate gloves and eye protection, ventilate the work area, and follow resin and cleaner safety instructions.
Which should you buy?
For two separate material or color jobs in one session, investigate the P1 and its optional kit first, including current software and heating limitations. For longer single-resin jobs where replenishment is useful, investigate the M7 Pro's feed and withdrawal setup and its cleaning requirements. If neither automation feature matters, compare the complete setup and replacement parts against a simpler resin printer. If liquid resin handling does not fit your workspace, consider a filament printer with its own material and detail tradeoffs.
Read our Photon P1 buyer assessment and P1 printer hub, or visit the P1 ratings and owner discussion for individual experiences. For the other machine, see the M7 Pro buyer assessment, M7 Pro printer hub and M7 Pro owner discussion.
Featured image: Anycubic manufacturer render.