What Materials Can the QIDI Max4 Print?

Official QIDI Max4 enclosed large-format 3D printer used for a material capability guide

Direct answer: QIDI's current Max4 comparison record explicitly lists PLA, ABS, PETG, TPU and PA-CF. PLA and PETG are the simplest everyday routes. ABS depends on the active chamber, surface, cooldown and ventilation. TPU depends on exact hardness, dryness and feed behavior. PA-CF is a strongly conditional abrasive composite that needs exact-grade drying, a verified wear-resistant nozzle and finished-part proof. QIDI writes “etc.” after that list, but “etc.” is not evidence that every nylon, polycarbonate, polypropylene, soluble support or high-temperature polymer is supported.

The Max4 gives those documented families unusually broad hardware headroom: a 370 °C toolhead ceiling, 120 °C bed ceiling and independently heated chamber listed up to 65 °C. Those are machine limits, not universal print settings or automatic approval. The exact filament grade, installed nozzle, minimum nozzle diameter, conditioning, plate interface, chamber process, ventilation and application still have veto power.

QIDI Max4 material compatibility at a glance

Material group Max4 verdict Decision that controls success
PLA Explicitly listed; straightforward Use the exact grade's profile and cooling; keep chamber heat low enough to avoid soft-feed and heat-creep problems.
PETG Explicitly listed; grade conditional Dryness, surface release, cooling, flow and large-footprint shrink matter more than the machine maximums.
ABS Explicitly listed; chamber and exposure conditional Use stable chamber conditions, a compatible surface, controlled cooldown and suitable ventilation; filtration is not universal clearance.
TPU Explicitly listed; hardness and feed-path conditional Verify Shore hardness, dry state, spool drag, path, retraction and speed; do not generalize one successful grade to every flexible.
PA-CF Explicitly listed; strongly conditional Confirm exact nozzle material and diameter, recovery drying, sealed handling, chamber, surface, wear and representative-part performance.
ASA, unfilled PA, PC, PP, PVA/BVOH and other composites Current exact-model confirmation required Do not expand “etc.” or transfer a Plus5, Q2, Plus4, filament-page or temperature claim to Max4.
PEEK, PEI/ULTEM, PPS, PPA, POM, PVDF and unlisted specialties Unsupported or poor fit by default A 370 °C toolhead, 120 °C bed and 65 °C chamber do not establish the complete qualified process these materials may require.

What the current official record actually establishes

QIDI's current comparison page identifies Max4 as a CoreXY fused-deposition printer with a 390 x 390 x 340 mm build envelope. It lists a direct extruder with hardened-steel dual gears, 370 °C maximum toolhead temperature, 120 °C maximum bed temperature, a second-generation independently heated chamber up to 65 °C and a three-stage filter combining G3 prefilter, H12 HEPA and coconut-shell carbon.

The same exact-model record names the supported-filament range as “PLA, ABS, PETG, TPU, PA-CF, etc.” That sentence proves the five named families. It does not define every grade hidden inside “etc.” and it does not say that every named spool works without conditions. QIDI's separate printer families have different hotends, chambers, build surfaces, feed options and published material lists, so a Plus5, Q2 or Plus4 result must not be transferred to Max4.

The listed 390 mm-class capacity also changes the material decision. A small coupon may succeed while a wide plate-size part curls, splits, accumulates residual stress or exceeds practical cooldown time. Use the large-format printer guide for the broader capacity decision; this page owns which materials the Max4 record actually supports and what must still be qualified.

PLA: supported, but the chamber is not automatically an advantage

PLA is the lowest-friction documented Max4 route for large visual models, fixtures used at ordinary room conditions and general prototypes. Start with the filament maker's current profile, not the Max4's temperature ceilings. High-flow, matte, silk, impact-modified, wood-filled and fiber-filled PLA can have different nozzle, cooling, abrasion and flow requirements even though “PLA” appears in the supported list.

More chamber heat is not automatically better for PLA. Excess ambient heat can soften filament too early in the feed path, reduce cooling margin on bridges and small features, or increase heat-creep risk. Use QIDI's exact operating guidance for the selected grade, preserve ventilation and cooling paths, and qualify the largest representative geometry rather than a small decorative test.

PLA printability does not prove suitability for a hot car, outdoor UV, sustained load, food contact, electrical insulation or structural safety. Choose the material from the real load and environment with the custom-part material chooser, then test the finished orientation and geometry.

PETG: supported, with drying and release decisions

PETG is explicitly listed and is often the practical next step when an owner wants more ductility or temperature margin than ordinary PLA. The Max4's enclosure can reduce drafts, but PETG rarely needs maximum chamber heat. Exact grade, dry state, cooling, volumetric flow, first-layer compression and surface release decide whether a large print stays clean and dimensionally useful.

Moist PETG can string, foam, form rough surfaces and weaken layer bonding. A maintenance box can preserve a prepared spool but may not recover a badly wet one. Follow the filament maker's recovery-drying instructions, keep the spool protected during a long print and avoid inventing a hotter cycle from the printer's limits.

PETG can bond aggressively to some smooth surfaces. Use QIDI's current Max4 plate instructions and the grade maker's release guidance; do not increase first-layer squeeze until removal becomes destructive. For a 390 mm footprint, print a representative corner or strip first and allow a controlled cooldown before judging release and flatness.

ABS: active chamber capability still needs ventilation

ABS is explicitly listed, and Max4's independently heated chamber is the most relevant hardware control for it. Stable chamber conditions can reduce gradients that cause warping and layer splitting, especially on wide parts. They do not erase shrink, geometry, surface or cooldown limits. Use the exact grade's settings, a compatible build interface and a controlled cooldown before opening the enclosure or removing the part.

QIDI's three-stage filter is a useful engineering control, not proof that every emission is removed or that an occupied room is appropriate. Filament formulation, temperature, maintenance and room ventilation matter. Follow current QIDI instructions and the filament safety data, provide suitable source control and ventilation, replace filters on the prescribed schedule and do not use odor as an exposure meter. The ABS and ASA printer guide owns the cross-machine purchase decision.

ASA is related to ABS but is not named in the exact Max4 list used here. Do not silently convert ABS support into ASA support. Obtain current written Max4 confirmation and an exact grade process before accepting weather-exposed work.

TPU: the family name is not a hardness specification

QIDI explicitly lists TPU, but not a Shore hardness, brand or complete feed route in the comparison record. A mainstream 95A grade and a very soft flexible can behave like different processes. Softer filament buckles and compresses more easily, while a high-flow formulation can demand a different temperature and speed window.

Verify the exact grade's hardness, dry state, spool drag, path, retraction and flow limit. The Max4 record says filament-tangle detection requires QIDI BOX, but that statement does not prove every TPU works through the BOX or any multi-spool path. Use only a path QIDI documents for the exact flexible grade. If current instructions call for external or direct feeding, preserve that boundary.

The TPU drying guide helps separate wet-filament symptoms from feed trouble. For seals, grippers, bumpers and flexures, qualify tear initiation, compression set, flex life, bond lines and dimensional recovery. A printable flexible object is not automatically a pressure seal, medical device or safety component.

PA-CF: supported does not mean ready from an open spool

PA-CF is the only carbon-fiber material named in QIDI's exact Max4 list. It is also the most conditional named family. Carbon fiber is abrasive, but the comparison record used here specifies hardened-steel dual drive gears without identifying the installed nozzle material. Confirm the exact current nozzle, minimum nozzle diameter and replacement guidance before loading the grade. Do not infer a hardened nozzle from hardened gears.

Nylon composite capability includes moisture control. Follow the exact spool's recovery-drying time and temperature, transfer it without reabsorbing moisture and keep it protected through the full print. Use the nylon drying-versus-storage guide to separate recovery from maintenance. A dry box is not automatically a recovery dryer.

Large PA-CF parts still need a compatible surface, chamber process, shrink allowance and slow controlled cooldown. Carbon fiber can improve stiffness and dimensional behavior, but it does not guarantee layer-direction strength, impact resistance, fatigue life or thread durability. The nylon and carbon-fiber printer guide owns the broader printer choice. For Max4, validate representative geometry under real load, temperature, humidity and fastener conditions.

Why “etc.” stays confirmation-required

The current Max4 record does not explicitly name ASA, unfilled PA, PC, PP, PVA, BVOH, PLA-CF, PETG-CF, glass-filled materials or other composites. Some may later receive a current QIDI profile or manual route, but the word “etc.” is not enough to publish that claim. Require an exact-model source that identifies the material family, installed hardware, surface, chamber or feed conditions and any QIDI BOX boundary.

Do not use another QIDI printer's list as substitute evidence. A Plus5 material claim can depend on its hotend, chamber, plate, firmware and accessories. A Q2 or Plus4 profile can have a different envelope or lifecycle. Similar temperatures show only partial overlap; they do not establish warranty, service, firmware profile or complete-process support.

Soluble supports also require more than extrusion temperature. PVA and BVOH are moisture-sensitive and must bond to the selected model material during printing, survive its chamber and bed conditions, then dissolve under a controlled waste process. Pause until QIDI documents the exact Max4 and feed-path combination.

High-temperature and specialty polymers remain poor fits by default

PEEK, PEI/ULTEM, PPS, PPA, POM and PVDF are not named in the exact Max4 list used here. A 370 °C toolhead ceiling does not establish required melt stability, residence time, corrosion resistance, nozzle construction, bed interface or firmware profile. A 65 °C chamber is also not an industrial high-temperature chamber merely because the hotend can reach a higher number.

Some specialty polymers need substantially hotter and more uniform environments, tightly controlled drying, specialized surfaces, fume or decomposition controls and application-specific annealing. POM and some fluorinated or high-temperature materials create additional decomposition concerns if overheated. Do not improvise. Select equipment with explicit current manufacturer support and a facility designed for the process, or use a qualified production service.

Eight checks before a non-routine Max4 spool

  1. Exact-model evidence: confirm that current QIDI Max4 documentation names the family; do not rely on “etc.” or another printer.
  2. Exact grade: use the current technical and safety data for that formulation, color and reinforcement.
  3. Nozzle and path: verify installed nozzle material, diameter, wear state, drive path and QIDI BOX compatibility when relevant.
  4. Conditioning: distinguish recovery drying from maintenance storage and protect the spool during a long build.
  5. Surface: use the approved plate, release layer or adhesive and test removal after full cooldown.
  6. Environment: select chamber and cooling conditions for the grade; more chamber heat is not always better.
  7. Exposure and fire controls: follow QIDI instructions and the safety data for ventilation, filter service, electrical clearance and unattended-operation boundaries.
  8. Finished-part acceptance: test dimensions, layer strength, creep, fatigue, heat, weather, chemicals and fasteners on representative geometry.

If any link lacks evidence, the material is not yet qualified. The correct next step is written confirmation or a controlled representative trial under manufacturer instructions—not a claim that the toolhead gets hot enough.

Safety and finished-part boundaries

Operate the Max4 and QIDI BOX under current QIDI instructions, with correct electrical supply, clearances, guards, cooling paths and maintenance. Hot surfaces, moving mechanisms and a large heated enclosure create burn, pinch, fire and electrical risks. Do not defeat interlocks or filters, and do not leave a new high-temperature or long-duration process unattended until the equipment instructions and local risk controls permit it.

NIOSH's safer-3D-printing guidance treats enclosure, ventilation, filtration, housekeeping and material choice as parts of a hierarchy of controls. The built-in filter is not a substitute for the exact filament safety data, room assessment, source control or industrial-hygiene advice. Control dust when cutting or sanding carbon-fiber parts and use suitable PPE under the material documentation.

A printable part is not automatically approved for food or potable-water contact, medical use, pressure containment, mains electrical insulation, flame performance, vehicle-control duty or structural safety. Formulation, contamination, orientation, voids, creep, fatigue, fasteners and finishing all matter. Use traceable, regulated production when failure consequences are high.

Buyer and owner decision

  • Buy or keep Max4 when large enclosed PLA, PETG or documented ABS work is the main need and representative geometry fits the 390 x 390 x 340 mm envelope.
  • Use TPU only after the exact hardness and feed route are documented; do not assume every flexible works through QIDI BOX.
  • Use PA-CF when the exact grade, verified nozzle, recovery drying, sealed handling, surface, chamber and part qualification are acceptable recurring work.
  • Get current written confirmation for ASA, ordinary PA, PC, PP, soluble supports or composites not explicitly named in the exact-model record.
  • Choose another qualified machine or service when an unlisted high-performance polymer, hotter controlled chamber, certified exposure control or regulated traceability is mandatory.

For a defined part, request a scoped GoodPrints quote; for repeat production and broader equipment access, use the JC Print Farm route. A quote does not replace application, safety or regulatory qualification.

Bottom line

The defensible current Max4 list is PLA, ABS, PETG, TPU and PA-CF. PLA and PETG are the cleanest lane; ABS depends on chamber, surface, cooldown and ventilation; TPU depends on hardness and feed route; and PA-CF depends on exact nozzle, drying, wear and part proof. Keep every “etc.” material confirmation-required and every unlisted specialty polymer unsupported or poor-fit by default until QIDI publishes an exact Max4 process.

Official sources checked