What Materials Can the Craftbot FLOW Print?

Official Craftbot FLOW single-extruder 3D printer used for a comprehensive material guide

Direct answer: Craftbot's FLOW product sheet explicitly lists PLA, ABS, HIPS, PET and nylon for its 1.75 mm single-extruder system. The current product page also presents PET-G filament as a FLOW add-on. PLA and ordinary PET/PET-G are the cleanest stock choices. ABS, HIPS and nylon are genuinely manufacturer-listed, but the open-frame environment, exact grade, moisture, bed interface and ventilation can make them conditional. The sheet ends its list with “etc.”; that word is not evidence that TPU, ASA, PC, carbon-filled or high-temperature polymers are officially supported.

The FLOW has an all-metal hotend, a documented 180-300 °C operating nozzle range, a 30-110 °C heated-bed range and a standard 0.4 mm nozzle. Those numbers are operating limits, not a universal material formula. Craftbot's page references a hardened-steel nozzle kit and a cover set, but the linked shop routes returned 404 during this review. Confirm the installed nozzle, available cover, replacement parts and current Craftbot support before buying around a conditional material.

Craftbot FLOW material compatibility at a glance

Material group Verdict Decision that matters
PLA Manufacturer-listed; straightforward stock fit Use the exact grade's profile and keep the bed interface clean; filled PLA moves into the abrasion decision.
PET and PET-G/PETG PET is listed; PET-G is shown as a product-page add-on Moisture, flow, cooling and safe release from the chosen surface matter more than the 300 °C ceiling.
ABS Manufacturer-listed; environment-conditional FLOW is open-frame. Part size, drafts, room stability, cover availability, cooldown and emissions controls can veto the job.
HIPS Manufacturer-listed as a printable filament The base FLOW has one extruder, so listing HIPS does not create simultaneous ABS-plus-HIPS soluble-support capability.
Nylon Manufacturer-listed family; strongly grade-conditional Drying, storage, nozzle temperature, surface, room stability and the exact PA6/PA12/copolymer formulation decide the process.
TPU/TPE Not established by the exact official list Require hardness-specific feed guidance; an all-metal hotend does not prove that a soft filament will reach it reliably.
Wood, metal, carbon- or glass-filled grades Do not assume stock support Confirm nozzle material, minimum diameter, drive-path wear, drying and replacement parts; the hardened kit is referenced but not included by the page.
ASA, PC, PP, PVA/BVOH and other specialties Conditional or workflow-poor by default They are absent from the exact list and may require chamber, surface, feed, paired-extruder or ventilation evidence the stock FLOW record does not provide.
PEEK, PEKK, PEI/ULTEM, PPS/PPSU and similar high-temperature polymers Unsupported or poor fit A 300 °C nozzle ceiling and open frame do not establish the complete high-temperature process these grades require.

What Craftbot's current records actually establish

The FLOW page and the single-extruder FLOW-generation product sheet describe fused-filament fabrication with 1.75 mm filament, a standard 0.4 mm nozzle and a 300 × 200 × 250 mm build volume. The heated platform combines metal, tempered glass and Kapton with a flexible top plate. The page also identifies an all-metal hotend, filament monitoring, mesh bed leveling and a single print head. These are useful process facts, but they do not identify every installed nozzle alloy, every compatible coating or every formulation inside a polymer family.

The same product sheet covers the taller single-extruder FLOW XL, which changes Z height rather than the documented filament list, nozzle range or bed range. This page therefore owns the broad material decision for both single-extruder FLOW sizes. A separate FLOW XL material article would swap a height number without creating a different material decision. FLOW IDEX machines can remain separate where two independent extruders create a real paired-material or support workflow.

Lifecycle evidence is current enough to make the operating decision useful. Craftbot's firmware page explicitly includes FLOW and FLOW XL and lists a Flow-generation release dated March 31, 2026. That does not prove that every printer, spare part or accessory is in stock. The product page's shop links for the FLOW collection, hardened-steel nozzle kit, cover set and PET-G add-on returned 404 during execution-time checks. Owners should use Craftbot support or an authorized source to confirm current configuration, part identity and service rather than treating a stale shop link as availability.

That distinction matters most on a used machine. A seller's “FLOW” label does not document nozzle alloy, wear, replacement top plate, sensor condition, firmware, prior abrasive use or whether an apparent cover is the supported Craftbot assembly. Ask for clear hardware photos, the serial and configuration, a cold inspection, heat-up and sensor checks performed under safe instructions, and a representative print in the material lane you actually need. Treat missing service records and unavailable replacement parts as ownership costs, not as proof that the material itself is impossible.

PLA: the cleanest stock lane

PLA is explicitly listed and is the lowest-friction reason to use the FLOW. The standard 0.4 mm path, heated platform and open frame suit ordinary prototypes, organizers, display parts and light-duty fixtures when the exact grade's profile is followed. Start from the filament maker's range, not the hotend maximum. A 300 °C limit is capacity, not a PLA target.

“PLA” still does not establish service performance. PLA+, PLA Pro, high-flow, recycled, matte, silk, glow and mineral-filled products can differ in abrasion, brittleness, flow and heat resistance. A part that prints cleanly can still creep under sustained load or soften in a sun-heated enclosure. Use the custom-part material chooser to start from load, heat, weather, chemicals and failure consequence rather than choosing a material from printability alone.

PET and PET-G: good fit, exact identity matters

The product sheet says PET, while the current FLOW page presents PET-G filament among its add-ons. Those records support PET/PET-G as a practical FLOW lane, but they do not make every PET, PETG, PET-G, CPE or glycol-modified blend identical. Use the exact spool's technical data, keep its moisture history controlled and select cooling and flow for that formulation.

PETG can string, pop, blob or produce rough surfaces when wet. The PETG drying-versus-storage guide separates recovery conditioning from routine sealed storage. Also follow the current surface instructions: PETG can bond aggressively to some clean sheets, while an overlarge first-layer gap can create weak adhesion. The FLOW's layered bed description does not authorize one release procedure for every replacement top plate.

ABS and HIPS: listed, but the room and single extruder matter

Craftbot lists ABS and HIPS, so neither should be labeled unsupported. The base FLOW is nevertheless an open-frame printer. Wide ABS footprints, sharp corners, tall walls and abrupt cross-section changes can shrink unevenly, lift or split when room air changes. A small bracket in stable air is not the same operating decision as a large enclosure panel. If ABS or ASA is the recurring workload, compare purpose-built enclosed options in the ABS and ASA printer guide.

The product page references a FLOW cover set, but its linked shop route was unavailable during this check. Do not assume a used printer includes it or that an improvised cover is equivalent. Confirm the exact Craftbot part and installation instructions. Any enclosure must preserve electronics cooling, clearances, access and fire precautions. A passive cover also does not create a specified active chamber or prove uniform air temperature.

HIPS has two possible roles: a printable styrenic material and, in suitable paired systems, a dissolvable support for ABS. The stock FLOW is single-extruder. It can print one loaded material, but the official list does not create an automatic model-plus-HIPS support workflow. For recurring two-material supports, use the multi-toolhead and independent-extruder guide and compare a machine designed around the pairing.

ABS and HIPS also require an exposure-control decision. Follow the material safety data and Craftbot instructions. NIOSH's safer-3D-printing guidance treats source capture, ventilation and high-efficiency filtration as engineering controls. An enclosure can reduce drafts without proving that ultrafine particles or volatile compounds are safely captured. Odor is not an exposure measurement.

Nylon: manufacturer-listed, not universally easy

“Nylon” in the official sheet establishes family-level intent, not support for every PA6, PA12, copolyamide, filled or flexible grade. Different nylons can require different nozzle temperatures, bed interfaces, ambient stability and conditioning. Some may sit inside the machine's numeric limits and still be poor choices because the surface, open room or moisture process is not controlled.

Drying is usually the first gate. Nylon can absorb enough moisture to cause bubbles, rough surfaces, weak bonding and dimensional drift. Recovery drying and maintenance storage are different tasks; use the nylon drying-versus-storage guide and the filament maker's current schedule. Confirm that the dryer is rated for both the required temperature and the spool material. Loading a wet spool and raising the hotend temperature does not solve the moisture source.

Unfilled nylon also does not approve carbon- or glass-filled nylon. Fillers can increase abrasion and minimum-nozzle-size requirements. Craftbot references a hardened-steel nozzle kit for FLOW generation, but the current page does not say it is stock, and the linked shop page returned 404. Inspect the installed nozzle rather than inferring it from the machine name. If reinforced nylon is the workload, the nylon and carbon-fiber printer guide helps compare systems with an explicitly documented hardened path and enclosure.

TPU, filled filaments and soluble supports: hardware evidence comes first

TPU and TPE are not named in the exact FLOW product-sheet list. Some harder flexible grades may publish temperatures inside the machine range, but temperature does not establish reliable feeding. Shore hardness, spool drag, drive geometry, unsupported path length, retraction and moisture can cause buckling or grinding before the filament reaches the hotend. Require Craftbot or exact-grade guidance before presenting TPU as supported.

Wood, metal, carbon, glass, mineral and glow fillers introduce a different issue. They may be abrasive, brittle or particle-laden. Confirm the installed nozzle alloy and diameter, the filament maker's minimum orifice, drive-component wear, drying and replacement-part access. A hardened nozzle may change thermal behavior, and installing one does not upgrade every component the filament touches.

PVA and BVOH are moisture-sensitive support materials. The base FLOW has one extruder, so a soluble filament cannot serve as simultaneous support for a different model material in the ordinary workflow. Printing the support polymer by itself proves little about a paired process. A manual material change at a layer boundary is not equivalent to independent dual extrusion for complex interfaces.

ASA, PC, PP and high-temperature polymers: do not extrapolate from 300 C

ASA is related to ABS, but it is not in the exact list used here. PC covers many formulations with different heat and chamber needs. PP brings low surface energy and shrink. Some grades may be experimentally printable, but the current FLOW records do not establish the full environment, surface or application process. Treat them as conditional and unqualified unless the exact filament supplier and Craftbot document a compatible workflow.

PEEK, PEKK, PEI/ULTEM, PPS, PPSU, PSU, PVDF and similar high-performance polymers are poor default fits. A maximum nozzle temperature does not establish melt stability, chamber temperature, bed chemistry, crystallinity, drying, annealing, emissions or finished-part properties. The open-frame FLOW is not documented as a high-temperature industrial cell. If those polymers are the requirement, choose equipment and facility controls explicitly designed around the exact grade.

Six checks before loading a non-routine spool

  1. Exact formulation: obtain the current technical and safety data; a family name is not a shared recipe.
  2. Installed hardware: inspect nozzle material and diameter, drive path, surface and any genuine Craftbot cover rather than assuming an accessory is included.
  3. Complete temperature window: compare nozzle, bed, ambient or chamber, cooling and degradation limits; do not use maxima as settings.
  4. Conditioning: separate recovery drying from storage and verify that the dryer and spool can safely follow the material schedule.
  5. Exposure and fire controls: follow Craftbot and material instructions, preserve clearances and cooling, and use appropriate source control and ventilation.
  6. Part acceptance: qualify representative geometry for dimensions, layer strength, creep, fatigue, heat, weather, chemicals and the actual failure consequence.

If one check has no evidence, the answer is not “the hotend reaches 300 °C.” The process is not yet qualified. The Bambu Lab P2S material router shows what a broader current consumer platform documents, but its support list and hardware must not be transferred to the Craftbot.

Safety and finished-part limits

Use current Craftbot operating instructions and firmware guidance. Keep hot and moving components guarded from contact, maintain the machine and bed surface, preserve electronics ventilation, and do not defeat sensors or install undocumented electrical modifications. A cover, filter or room fan needs a deliberate plan; none turns every polymer into a safe occupied-room process. Qualified local professionals and the authority having jurisdiction decide final electrical, fire and workplace controls.

Cutting, drilling or sanding filled parts can create fine dust and exposed fibers. Use local extraction, housekeeping and PPE suitable for the exact material. A printable part is not automatically approved for food contact, potable water, medical use, pressure containment, mains insulation, fire barriers, vehicle controls or lifting. Grade identity, colorants, layers, voids, creep, fatigue, fasteners and post-processing can dominate service behavior.

Buyer and owner decision

  • Keep or buy the FLOW for a straightforward single-extruder PLA and PET/PET-G workflow, with carefully bounded ABS, HIPS and exact-grade nylon work.
  • Confirm configuration first when a used or existing printer's nozzle, top plate, cover, firmware or service history is unknown.
  • Choose an enclosed, abrasion-ready machine when ABS/ASA, reinforced nylon or other filled materials are the recurring workload rather than an occasional qualified job.
  • Choose an IDEX or multi-tool system when soluble or breakaway support must run beside the model material.
  • Use qualified external production when high-temperature polymers, traceability, regulated evidence or facility controls matter more than owning this machine.

For a defined part, request a GoodPrints quote; the custom-printing service FAQ explains the required inputs. For repeat production and broader equipment access, use the JC Print Farm route.

Bottom line

The Craftbot FLOW has an explicit manufacturer material lane: PLA, ABS, HIPS, PET and nylon, with PET-G also presented on the current product page. PLA and PET/PET-G are the clean stock choices. ABS, HIPS and nylon are real but conditional on the exact grade, environment, surface, conditioning and exposure controls. Do not turn “etc.,” an all-metal hotend or a 300 °C ceiling into support for every flexible, filled or high-temperature polymer. Buy around the complete recurring process and confirmed current parts, not one temperature number.

Official sources checked