LulzBot TAZ Workhorse vs Original Prusa MK4S: Build Space, Filament, and Buying Tradeoffs

GoodPrints3D logo

Quick take: The legacy LulzBot TAZ Workhorse offers the larger documented build envelope, at 280 × 280 × 285 mm, while the Original Prusa MK4S is listed at 250 × 210 × 220 mm. Their documented filament paths also differ: the Workhorse's stock SE tool head uses 2.85 mm filament, while Prusa lists 1.75 mm filament for the MK4S. Those differences make the Workhorse worth investigating when a project needs its larger stated envelope and the buyer can verify an older machine's condition and configuration; the MK4S is the more direct fit for someone whose existing workflow uses 1.75 mm filament. These are manufacturer specifications, not measurements or comparative print tests by GoodPrints3D.

For exact-model details, read the LulzBot TAZ Workhorse buyer guide, the LulzBot TAZ Workhorse specifications and guide, and the owner discussion. Use the interactive printer comparison tool to compare supported specifications for other models.

At a glance

Specification LulzBot TAZ Workhorse Original Prusa MK4S
Documented build volume 280 × 280 × 285 mm (22.344 L) 250 × 210 × 220 mm (11.55 L, calculated)
Documented filament diameter 2.85 mm in the stock SE tool-head specification 1.75 mm
Documented stock extruder/nozzle Single extruder, 0.5 mm nozzle Nextruder direct drive; listed high-flow 0.4 mm brass CHT nozzle
Heated bed maximum Up to 120 °C in the Workhorse specification sheet 120 °C

Values come from the respective manufacturers' published specifications. Tool heads, optional equipment, machine condition, and usable clearance can affect an individual setup. The Workhorse values describe its documented stock SE tool head; inspect a used unit rather than assuming it remains stock. No speed, accuracy, reliability, print-quality, or total-cost winner is claimed.

Build space: the Workhorse has more room on paper

LulzBot lists the TAZ Workhorse build area as 280 × 280 × 285 mm. Prusa lists 250 × 210 × 220 mm for the MK4S. The Workhorse's published envelope is larger on all three axes. LulzBot lists its volume as 22.344 L; multiplying Prusa's published dimensions gives 11.55 L for the MK4S. These figures describe the rectangular stated envelope, not a guarantee that every design fits in one piece. A listed envelope does not guarantee that a particular design fits after accounting for supports, brim, clips, orientation, or the condition and setup of a used machine. Neither figure is an independent measurement by GoodPrints3D.

For smaller objects, the difference may not affect the job. Check the oriented model dimensions against the exact machine and slicer profile. If the job can be split and assembled, compare the extra joints and finishing work with the value of printing it in one piece.

Filament and stock hardware

The LulzBot specification sheet describes the standard Workhorse SE tool head as one extruder with a 0.5 mm nozzle for 2.85 mm filament. Prusa's MK4S specification lists 1.75 mm filament and a Nextruder direct-drive extruder with a 0.4 mm high-flow brass CHT nozzle. Filament diameter and tool-head details are configuration facts, not a promise of material compatibility or print results. On a second-hand Workhorse, confirm the installed tool head, nozzle, filament path, wiring, and firmware/profile before buying.

If your shop already stocks 1.75 mm filament, the MK4S fits that supply without changing diameter. A Workhorse buyer should account for suitable 2.85 mm material and verify its local availability. Do not infer that one machine prints faster or better from nozzle diameter alone.

Which one fits your buying situation?

Consider the TAZ Workhorse when you need its larger stated single-part envelope, prefer its open-hardware and repair documentation, and are prepared to evaluate a legacy machine carefully. The available evidence does not verify a current offer for this exact legacy model. Treat listings as used or remaining stock and verify model identity, condition, installed parts, completeness, and support needs at listing level. Do not confuse it with the later TAZ Workhorse 2 or Workhorse+.

Consider the Original Prusa MK4S when its smaller published build volume is sufficient and you want the manufacturer's documented 1.75 mm filament setup. Prusa publishes current MK4S technical parameters and package options on its product page. This comparison does not verify current price, stock, shipping, or warranty terms for a buyer's location; check the seller's current listing directly.

Neither specification sheet settles reliability, maintenance burden, print quality, total ownership cost, or suitability for a particular material. The Workhorse comparison is especially dependent on the actual used unit's configuration and condition. Ask for a current demonstration and inspect the machine before purchase; a seller demonstration is not an independent test.

Sources and limits

Manufacturer statements are attributed as specifications. No hands-on comparison, benchmark, current price, live offer, or stock check is represented. No independent testing was verified.

Image credit: GoodPrints3D site logo. The logo is not an image of either printer.