EOS P 396 vs EOS P 500: Build Volume and Production Considerations
The EOS P 396 and EOS P 500 are industrial polymer laser sintering systems with different build envelopes and laser configurations. The P 396 offers more height, while the P 500 offers a longer X dimension. The right choice depends on the parts, material and complete production cell, not one headline specification. This comparison uses manufacturer data and is not a hands-on test. See the EOS P 396 printer hub and buyer guide for more context.
At a glance
- Process: Both use polymer selective laser sintering.
- Build volume: P 396: 340 × 340 × 600 mm. P 500: 500 × 330 × 400 mm.
- Laser: P 396: one 70 W CO₂ laser. P 500: two 70 W CO₂ lasers.
- Maximum scan speed: P 396: up to 6.0 m/s. P 500: up to 10.0 m/s.
These are manufacturer specifications from the EOS P 396 data sheet and EOS P 500 data sheet. The P 500 figures refer to the P 500, not the separate P 500 FDR. The quoted scan speeds are maximum values, not measurements of finished-part output. Laser count alone does not establish throughput either.
Which build volume suits the parts?
Start with the largest parts and the orientation they need. The P 396 has 200 mm more nominal Z height and 10 mm more Y width. The P 500 has 160 mm more X length. A tall part that fits within the P 396's height may be a reason to investigate it first; a long part that needs the P 500's X dimension may point the other way. Neither example proves a particular part will fit or meet its tolerance.
Bring the actual part geometry to EOS and ask for a proposed orientation and clearance in each system. Allow for the whole job layout, not just a bounding box. Consider how many different parts must share a build and how their orientation affects the surfaces and dimensions that matter to the application. A nominal envelope is not a guarantee of usable nesting density, packed yield or finished-part accuracy. If a part is close to an axis limit, seek confirmation for the material and configuration before using that fit as a purchasing assumption.
Comparing production capacity
The P 500's two lasers and higher maximum scan speed are meaningful specifications, but they are not a direct multiplier for the number of accepted parts per day. A useful comparison follows a representative job from preparation through cooling, unpacking, finishing and inspection. The mix of part sizes, nesting, material and settings can change both the build and the work around it.
Ask each proposal to use the same part files, quantities, material, acceptance criteria and planning horizon. Request the assumptions behind estimated cycle time and output, including whether estimates cover cooling and downstream work. Separate an equipment estimate from a demonstrated result, and ask how rejected parts, operator coverage and planned maintenance are handled. If possible, qualify representative parts and use the resulting yield and measured workflow in the business case.
The P 500 data sheet describes a two-roller recoater and automation interfaces for industrial production. These are manufacturer descriptions, not proof that a particular cell will run unattended or meet a buyer's target. Confirm the accessories and staffing in the quote and test the proposed workflow against the actual shift pattern.
Materials and part qualification
Both EOS data sheets list PA 2200, providing a common starting point for a comparison. A shared material name does not by itself establish identical properties, processing settings or suitability for a regulated or load-bearing application. Confirm the exact powder, parameter set and current machine configuration with EOS, then qualify finished parts for the intended use.
Define what acceptance means before ordering sample parts: critical dimensions, surface requirements, mechanical performance and any documentation the application requires. Compare results made under stated conditions rather than treating a material listing as a performance guarantee. If the intended material is different from PA 2200, check its availability and supported process on each exact model before using it as a basis for the decision.
Powder handling, software and the production cell
The printer is only part of the workflow. EOS lists optional powder handling, unpacking and sieving equipment and a blasting cabinet for both systems. Ask which items are included, which are optional and how powder is transferred, recovered and handled in the proposed configuration. Plan space and labor for unpacking and finishing as well as the printer itself. Site and safety requirements should come from current EOS documentation and the facility's own assessment.
EOS lists its System Suite for both machines, while the P 500 data sheet also describes EOS Build subscriptions. Confirm the software, licenses, training and integration included in each proposal. For a production workflow, ask how job preparation, traceability and quality records fit the systems already used at the site. Features described in a data sheet should be checked against the quoted configuration and contract.
Compare the complete cost and the alternatives
Request current complete-cell quotations, site preparation documents, training, service terms, lead times and optional equipment from EOS. Include powder, consumables, utilities, labor, maintenance and finishing in the operating model. Compare the same workload and acceptance criteria for each machine, and ask which assumptions are included in any supplier estimate. Current prices, availability and independent production measurements have not been verified here.
For intermittent demand, compare that ownership model with outsourcing the same representative work, including delivery and qualification requirements. If the part or required material does not fit either proposed configuration, evaluate another machine or process. A purchase decision should rest on qualified parts and a workable production cell, not on the largest nominal axis or fastest stated scan speed alone.